Florian Wittemann Florian Wittemann

Dr.-Ing. Florian Wittemann

Veröffentlichungen


Influence of fiber breakage on flow behavior in fiber length- and orientation-dependent injection molding simulations
Wittemann, F.; Kärger, L.; Henning, F.
2022. Journal of Non-Newtonian Fluid Mechanics, 310, 104950. doi:10.1016/j.jnnfm.2022.104950
Design Approach for a Novel Multi Material Variable Flux Synchronous Reluctance Machine without Rare Earth Magnets
Kesten, J.; Frölich, F.; Wittemann, F.; Knirsch, J.; Bechler, F.; Kärger, L.; Eberhard, P.; Henning, F.; Doppelbauer, M.
2022. 2022 International Conference on Electrical Machines (ICEM), Valencia, Spain, 05-08 September 2022, 2304–2310, Institute of Electrical and Electronics Engineers (IEEE). doi:10.1109/ICEM51905.2022.9910780
Fiber-dependent injection molding simulation of discontinuous reinforced polymers. PhD dissertation
Wittemann, F.
2022, February 16. Karlsruher Institut für Technologie (KIT). doi:10.5445/IR/1000142956
Simplified modeling of electromagnets for dynamic simulation of transient effects for a synchronous electric motor
Bechler, F.; Kesten, J.; Wittemann, F.; Henning, F.; Doppelbauer, M.; Eberhard, P.
2021. International Journal of Mechanical System Dynamics, 1 (1), 89–95. doi:10.1002/msd2.12005
Direktgekühlter Elektromotor mit integralem Leichtbaugehäuse
Wittemann, F.; Kärger, L.; Henning, F.
2019, October 9. Fachtagung „Wärmeleitfähige Kunststoffe für das Thermomanagement“ (2019), Lüdenscheid, Germany, October 9, 2019
Injection Molding Simulation with Fiber Length Dependent Flow Modelling
Wittemann, F.; Kärger, L.; Henning, F.
2019, May 8. 12th International Conference on Composite Science and Technology (2019), Sorrento, Italy, May 8–10, 2019
Evaluation of an Integral Injection Molded Housing for High Power Density Synchronous Machines with Concentrated Single-Tooth Winding
Langheck, A.; Reuter, S.; Saburow, O.; Maertens, R.; Wittemann, F.; Berg, L. F.; Doppelbauer, M.
2019. 2018 8th International Electric Drives Production Conference (EDPC), 4 and 5 December 2018, Schweinfurt, Germany: Proceedings, Art.-Nr.: 8658324, Institute of Electrical and Electronics Engineers (IEEE). doi:10.1109/EDPC.2018.8658324
Simulation of Insert Deformations for Thermoset Materials
Wittemann, F.; Kärger, L.; Henning, F.
2018, June 5. 9. CONNECT! European Moldflow® User Conference (2018), Frankfurt am Main, Germany, June 5–6, 2018
Simulation of Discontinuous Fiber Reinforced Composites along the CAE-Chain
Wittemann, F.; Hohberg, M.; Kärger, L.; Henning, F.
2018, March 7. MAHLE R&D Networking - High Performance Plastic (2018), Stuttgart, Germany, March 7–8, 2018
Vorstellung DEmiL – Direktgekühlter Elektromotor mit integralem Leichtbaugehäuse
Wittemann, F.; Kärger, L.; Henning, F.
2018, January 23. 20. Leichtbauforum des LBZ-BW e.V. (2018), Renningen, Germany, January 23, 2018
Strömungsmechanische Simulationen zur Herstellung von Faserverbundbauteilen
Henning, F.; Seuffert, J.; Wittemann, F.
2018, January 15. Strömungsmechanik und Strömungsmaschinen (2018), Karlsruhe, Germany, January 15, 2018
Using openfoam for simulation of reactive injection molding as a non-isothermal compressible multiphase flow
Wittemann, F.; Maertens, R.; Kaerger, L.; Henning, F.
2018. 14th International Conference on Flow Processing in Composite Materials, Luleå, S, May 30 - June 01, 2018
Simulation of Reinforced Reactive Injection Molding with the Finite Volume Method
Wittemann, F.; Maertens, R.; Bernath, A.; Hohberg, M.; Kärger, L.; Henning, F.
2018. Journal of composites science, 2 (1), Aritcle no: 5. doi:10.3390/jcs2010005
Modeling of the Non-Isothermal Crystallization Kinetics of Polyamide 6 Composites During Thermoforming
Kugele, D.; Dörr, D.; Wittemann, F.; Hangs, B.; Rausch, J.; Kärger, L.; Henning, F.
2017. Proceedings of the 20th International ESAFORM Conference on Material Forming, ESAFORM 2017, Ireland, Dublin, 26th - 28th April 2017, Art.Nr. 030005, American Institute of Physics (AIP). doi:10.1063/1.5007992